Shuttle DS407T
Shuttle DS407T
Compra Ya
x

Características técnicas

Especificaciones sujetas a cambio por parte del fabricante.
Fanless and silentPassive cooling, no fan noise at all
Perfect to be used in noise-sensitive environments
Fanless, dust-free and thus virtually maintenance-free
Low power consumptionPower consumption: idle: 10-11W, full load: 22-30W (without/with graphics)
(measured with 2x 2GB SO-DIMM, 500 GB 2.5" hard disk)
24/7 nonstop operationThis device is approved for 24/7 permanent operation.
Requirements:
- Free circulation of air amongst the PC must be guaranteed.
- Ventilation holes must stay clear.
- If a hard disk is installed, this must also be approved for permanent operation by its manufacturer
ChassisSlim-PC (Nettop) with black chassis made of steel
Without cooling fan, passive cooling only
The bays for memory, 2.5" drives and Mini-PCIe cards
can be easily accessed by removing two cover plates.
Dimensions: 200 x 165 x 39.5 mm (LWH) = 1.3 litres
Weight: 1.43 kg net and 2.13 kg gross
Two holes for Kensington Lock and numerous
threaded holes (M3) at both sides of the chassis
Operation Position:1) Device must only be used in vertical position with the DVI port facing up
2) Please make sure to use either the supplied feet or the VESA mount
Operation SystemThis barebone system comes without operating system.
It is compatible with Windows 8, Windows 7, Windows XP and Linux
Supports 32 and 64 bit.
ProcessorProcessor model: Intel Celeron 1007U (ULV)
Code name: Ivy Bridge (3rd Gen. Core)
Cores / Threads: 2 / 2
Clock rate: 1.5 GHz
L1/L2/L3 cache: 128 kB / 512 kB / 2048 kB
Memory controller: DDR3-1333/1600 Dual Channel
TDP wattage: 17 W maximum
Manufacturing process: 22 nm
Socket: FCBGA1023
Enhanced SpeedStep technology
Maximum Tjunction Temperature: 105°C
Integrated Intel HD graphics engine
Supports 64 Bit, VT-x with EPT, Enhanced SpeedStep, NX bit, SSE4
Integrated graphicsIntel HD graphics
Clock rate: 350~1000 MHz
Maximum resolution: 1920x1200 (analog or digital)
Execution Units (EU): 6
Supports two independent screens
Supports DirectX 11.1, OpenGL 4.0
Supports full AVC/VC1/MPEG2 hardware decoding
HDMI supports HD video plus multi-channel digital audio via a single cable
Mainboard / Chipset / BIOSShuttle Mainboard FS47
All capacitors are high quality solid capacitors
Chipset: Intel® NM70 Express
Supports resume after power failure
Supports Wake on LAN (WOL)
Supports Power on by RTC Alarm
Supports boot from USB devices and SD card reader
AMI BIOS in 8 MByte EEPROM with SPI interface
Supports hardware monitoring and watch dog functionality
Supports Unified Extensible Firmware Interface (UEFI)
Power AdapterExternal 65 W power adapter (fanless)
Input: 100~240 V AC, 50/60 Hz, max. 1.6 A
Output: 19 V DC, max. 3.42 A, max. 65 W
DC Connector: 5.5/2.5mm (outer/inner diameter)
Memory support2x SO-DIMM slots with 204 pins
Supports DDR3-1333 (PC3-10600) and DDR3-1600 (PC3-12800) SDRAM
Supports Dual Channel mode
Supports max. 8 GB per DIMM, maximum total size of 16 GB
Supports two unbuffered DIMM modules (no ECC)
Mini PCIe SlotHalf size Mini PCI Express expansion slots (occupied with a WLAN module)
AudioAudio Realtek® ALC 662 High-Definition Audio (5.1 channel)
Two analog audio connectors (3.5mm) at the back panel:
1) 2 channel line out (head phone)
2) microphone input
Digital multi-channel audio output: via HDMI
Gigabit LAN ControllerRealtek 8111G Ethernet network controller (Gigabit)
Supports 10 / 100 / 1.000 MBit/s operation
Supports WAKE ON LAN (WOL)
Supports network boot by Preboot eXecution Environment (PXE)
Wireless Network (WLAN)Built-in Mini-PCIe WLAN card (half size) and internal antenna
Single-Chip 1T1R WLAN Controller Realtek RTL8188CE
Supports IEEE 802.11b/g/n, max. 150 Mbps up-/downstream
Security: WPA/WPA2(-PSK), WEP 64/128bit, IEEE 802.11x/i
2.5Supports one Serial ATA hard disk
or one SATA SSD drive in 6.35cm/2.5" format
Device height: 9.5 or 12.5 mm (max.)
Supports Serial-ATA III, 6 Gb/s (600 MB/s) bandwidth
Supports Unified Extensible Firmware Interface (UEFI)
Note: no Serial ATA cable is required
Card ReaderIntegrated SD card reader
Supports SD, SDHC and SDXC memory flash cards
Supports boot up from SD card
Front Panel connectors2x USB 3.0
2x USB 2.0
SD card reader (supports SD, SDHC, SDXC)
Power button
Power LED (blue)
HDD LED (yellow)
Back Panel connectorsHDMI 1.3 connector (supports DVI-D with optional adapter)
DVI-I connector (supports VGA with optional adapter)
2x USB 3.0
2x USB 2.0
Gigabit LAN (RJ45)
Microphone input
Audio Line-out (headphone)
DC-input connector for external power adapter
4 pin connector (2.54 mm pitch) for power button, Clear CMOS and 5V DC
Perforation for optional Wireless LAN antennas (2 holes)
Other onboard connectorsLPC port (low pin count), 2x 10 pins for optional TPM module
Connector for CMOS battery (with battery)
Fan connector (4 pins) not occupied
Scope of deliveryMulti-language user guide
Two metal feet
VESA mount for 75/100mm standard (two metal brackets)
Four thumbscrews M3 x 5 mm (screws together VESA mount and PC)
Four screws M4 x 10 mm (to fix the VESA mount to the external device)
Three screws M3 x 4 mm and a rack (to mount a 2.5" storage into the bay)
Driver DVD (Windows 8 / 7 / XP)
External power adapter with power cord
Environmental SpecificationsOperating temperature range: 0~40 °C
Relative humidity, non-condensing: 10~90%
Conformity/CertificationsEMI: FCC, CE, BSMI, C-Tick
Safety: CB, BSMI, ETL
This device is classed as a technical information
equipment (ITE) in class B and is intended for use in
living room and office. The CE-mark approves the
conformity by the EU-guidelines:
- EMV-guideline 89/336/EWG electromagnetic tolerance
- LVD-guideline 73/23/EWG use of electric devices
within certain voltage-limits